|
|
Superflex
Description
Marley Superflex consists of a high quality fully flexible vinyl flooring
and wallcladding available in tile and sheet form and in various thicknesses.
Marley Superfiex combines a distinctive yet forgiving marble effect,
with high standards of performance in terms of durability and low maintenance.
Should a sealed, water-tight finish be required, Marley Superflex sheeting
can be welded with Superflex Welding Rod
 |
 |
Installation
Sub-Floors
Marley Superflex is suitable for installation on most types of sub-floors, but in the case of to earth concrete, it is essential that a damp-proof membrane is incorporated. Ensure that the sub-floor is completely smooth, level, hard, dry and clean before laying commences. The final appearance and ultimate wearability of the floor covering is governed by the surface upon which it is laid and care should be taken to ensure that the tight foundation is provided. All sub-floors are to be tested for moisture prior to installation. The Marley Technical Department can offer advice in this regard.
Welding
Marley Superflex may, 24 hours after installation, be welded, using a fully flexible Marley Welding Rod to provide a continuous surface. Wallcladding may be hot seam welded if required. A colour range of Marley Welding Rod is available to select from.
Adhesives
Marley No. 60 Acrylic Adhesive for floor tiles and sheeting, and Marley No. 71 Contact Adhesive for wallcladding are the recommended adhesives for use with Marley Superflex and should be applied in accordance with Marley's recommendations.
Maintenance
The newly laid Mariey Superflex floor should, after 72 hours be scrubbed with a diluted neutral detergent complying with SABS 825 and thoroughly rinsed. Apply three coats of a water based floor dressing complying to SABS 1042. Marley Superflex floors will retain their excellent appearance if an occasional application of floor dressing is applied.
Suggested Specification
Tiles
Supply and fix 20/2,5/3 0/3,5 mm thick x 300 mm x 300 mm Marley Superflex fully flexible vinyl floor tiles manufactured to SABS Specification 786-1992 laid in Marley No. 60 Acrylic Adhesive spread with a notched trowel having 1,5 mm x 1,5 mm x 1,5 mm triangular notches at 4,0 mm centres at the rate of between 5,5m² and 6,5m² per litre, on a previously prepared sub-floor by builder as cfescribed above and elsewhere measured including all cutting and waste. It is essential that on completion the installation be rolled, in both directions with an articulated 68kg three sectional metal floor roller.
Floor sheeting
Supply and fix 2,0/2,5/3,0/3,5 mm thick x 1,2 m wide Marley Superflex fully flexible vinyl floor sheeting manufactured to SABS Specification 786-1992 laid in Marley No. 60 Acrylic Adhesive spread with a notched trowel having 1,5 mm x 1,5 mm x 1,5 mm triangular notches at 4,0 mm centres at the rate of between 5,5 m² and 6,5m² per litre, on a previously prepared sub-floor by builder as described above and elsewhere measured including all cutting and waste. Joints to be butted, grooved and heat welded ensuring that the welding rod bonds to more than 70 % of the sheet thickness. It is essential that on completion the installation be rolled, in both directions with an articulated 68kg three sectional metal floor roller.
Wallcladding
Supply
and fix 1,0 mm*/ 1,25 mm thick x 1,2 m wide Marley Superflex fully flexible
wall- cladding manufactured to SABS Specification 786-1992, adhered with Marley
No. 71 Contact Adhesive, applied by means of a brush or paint roller
at the rate of approximately 3,5m2 per litre per single application
to both surfaces to be bonded, on a previously prepared wall surface by builder
as described above and elsewhere measured, including all cutting and waste.
* 1,0 mm wallcladding does not bear the SABS mark.
Colour
range and effect
The base range consists of 14 aesthetically pleasing colours and the trend range
consists of 6. Cornplementing the flooring are 8 pastel wallcladding colours
to select from.
For larg and special projects, an additional range of 48 Spectrum Colours are availible.
Underfloor heating
Marley Superflex is suitable for underfloor heating systems. It is, however, important that a screed temperature of 270ºC is not exceeded and therefore it is essential that a control thermostat be incorporated in the screed. The underfloor heating should be switched off for 48 hours prior to, during and 48 hours after the laying of Marley Supefflex flooring.
Fire resistance
Marley Superflex has self-extinguishing properties and will not contribute to the spread of flame. Mariey Superflex 1,25 mm, 2,0 mm and 2,5 mm thick material has an SABS fire classification rating of Class 1. Marley Superfiex 3,0 mm and 3,5 mm thick material has an SABS fire classification rating of Class 2.
Chemical resistance
The manufacturing process of Mariey Superflex ensures a natural resistance to attack by most acids, alkalis, common oils and greases and general household chemicals in diluted form. It is, however, recommended that the advice of the Marley Technical Department be obtained shoutd this material be subject to regular contact with chemicals and solvents.
Electrical properties
Marley Superflex can be classified as an electrically insulating floor covering.
Owing
to the limitations of colour printing processes and the possible effects of
different PC monitor settings, you are advised to see the actual material before
ordering.
BASE RANGE
Hazelnut MS085 |
Bone MS081 |
Cream Caramel
MS083 |
Wheat MS051 |
Cirrus MS031 |
Peach MS040 |
Lime MS061 |
Charcoal MS013 |
Menthol MS063 |
Wedgewood
Blue MS072 |
Ash Grey MS022 |
Whisper Grey
MS032 |
Pearl Mist
MS032 |
Signal Red
MS042 |
TREND RANGE
Purple Haze
MS073 |
Herb Green
MS062 |
Aquamarine
MS075 |
Salmon MS041 |
Antique Rose
MS043 |
Prussian Blue
MS074 |
WALLCLADDING RANGE
Powder Blue
MS372 |
White MS232 |
Hint of Grey
MS323 |
Aqua MS375 |
Light Salmon
MS241 |
Off-White
MS381 |
Hint of Corn
MS351 |
Blush MS543 |
Marley
Flooring
Technical Department - Johannesburg
(011) 681 4500
Export Department
Johannesburg
(011) 681 4500
FLOORING |
A
Division of Marley (SA) (Pty) Ltd. Reg. No.53/00406/07
Head Office (011) 681-4500 · Bloemfontein (051) 434-2331 ·
Cape Town (021) 951-2351
Durban (031) 469-0264 George (044) 873-2833 Gauteng (011) 908-5500
East London (043) 745 1019
Also available from:
Marley (Namibia) (Pty) Ltd. (0926461)23-7200
Contract Supplies (Botswana) (09267) 30-9650